Kinetico Water Softener Rebuild Kits Save $$$$$ Easy Fix Kit

  
Kinetico Water Softener Problems Fixed. Kinetico water softener problems can happen when sections of the Kinetico water softener control head breaks down. Parts inside the head such as the control valve which has two very important seals. The quad ring seal, and the taper seal, these are prone to wearing out. This also applies to the drain valve seals. The Kinetico drain valves have similar problems where they can wear on four edges. Another problem can happen when the Kinetico main piston seals wear on four edges, these are hidden seals which often get overlooked. The balance piston seal can cause problems too.

The very small advance seal located on the Kinetico actuator is particularly prone to wearing out. Generally, all the parts of the Kinetico need to work together to form a whole. The Kinetico pawl set, Kinetico control disk and Kinetico water meter disk must also be in perfect condition.

Brine tank resin can last up to 30 years, but needs to be good. Kinetico resin is installed in both the main tank and the remote tank. For best performance it is recommended to fit Kinetico resin. Resin is not generally a problem on the Kinetico, as 99% of all faults are linked with worn, non functioning seals.

Kinetico level one, has the most complex parts. This Kinetico level has the gears, the control disk, and the meter disk.

The pawl set is located on this level, as is the balance piston and DO cap. We show how to check this level. Kinetico level two has the vent tube and the brine flow control, the brine flow control can get blocked.

Kinetico level three has the venturi throat and the throat on this part of the Kinetico must be clear and perfect. We explain how to do this. Kinetico level four contains the main Kinetico piston flat seals and quad rings. Also, this level has the Kinetico control valve and quad rings, and of course the taper seal sets. In addition, there is the Kinetico backwash flow control.

This need to be clear and clean. Kinetico level five has the drain valves and quad rings. The Kinetico five level has the Kinetico interlock and the cut outs for the Kinetico check stems. Older versions have the small blue Kinetico balls that do the same job, to stop back flow in the system. Kinetico level six has the Kinetico check stems, and the Kinetico upper distributor.

The entire head is attached to the main Kinetico resin bottle by a large thread and immediately below that the upper distributor. The Kinetico seals involved in keeping this softener working are many, and only one Kinetico seal needs to be faulty to cause everything to fail.

We work through everything in detail in our Kinetico videos. We have many videos in detail, in fact detailed video for every level. Hours of information and explained by our Kinetico engineer.

Follow his work to get your Kinetico water softener working properly. We Need to Test Your Water. Here's How We Do That.

WHAT DO WE WANT FROM YOUR KINETICO SOFTENER?? We Want Beautiful Softened Water From it.

We Send You Our Simple Test Kit. We check the "HARDNESS" level of the water. HARD WATER DESTROYS EVERYTHING IT TOUCHES.

So, we check the water first before you start rebuilding. It's best to take a quick at the water coming from your softener first. We provide 2 test samples to check before rebuild and after. This is very simple to do with our easy dip tests. You Can Check Before Rebuild and Afterwards. Get Our Seal Kit - Videos - Engineers Guide. A VERY SIMPLE FIX IN A COUPLE OF HOURS. The Full Detailed Video Shows You What You Need And How to FIX IT. A tiny balance piston seal fault will cause your softener to continually run to the drain. This seal is probably responsible for 50% of all faults.

What do SOME Kinetico Engineers tell their customers? You probably need a new control head. Over 3 Hours Of Tutorials.

Here's The Amazing Thing??? Spare Parts Are Often NOT NEEDED. Not the entire block or head. WE SHOW YOU WHAT NO OTHER KINETICO DEALER WILL SHOW YOU. Repairs at a fraction of the price.. THIS KIT INCLUDES THE MAIN SEALS KITS? Kinetico Water Softener Re-Build Kits.

Universal Kinetico Softener Head Design. Upgraded Complete Seal Kit For All Kinetico Softener Heads. Kinetico Parts Included in this Kit. Control Valve Quad Ring Seals.

Purge Valve Quad Ring Seals. Drain Valve Piston Quad Ring Seals.

Drain Valve Internal Piston Quad Ring Seals. Outlet Valve Piston Quad Ring Seals. Outlet Valve Internal Piston Quad Ring Seals. Balance piston internal O rings seals. THESE ARE NO ORDINARY SEALS???

High Quality 4 Sides X Ring/Quad ring can often our exceed the originals in terms of. When these softeners get neglected and not serviced properly they often are not working to their full potential. They can "eat" salt like you wouldnt believe and not work at all efficiently. Almost all faults are solved by replacing a few essential seals within the water softener head itself.

Will this service Video apply and internal spare parts kit fit your Kinetico Water Softener? The simple answer is yes. The water softener head has a specific design and those very important seals will fit all designs.

They are all special seals that need to be a precise fit, consisting of the special X seals or Quad seals; these. Seals need to be fitted properly. Full contents of Video are shown here below. This kit now includes the Brand New Resin Change Video.

Brand New Videos - Video Format - Shows Step by Step. Shows EXACTLY how to do the entire job! 40 Minute Video - Easy to Follow. You will not get these parts from your local Kinetico dealer?

Kinetico have a policy of only supplying parts to their authorised installers and dealers. In addition, they do not sell the quad rings and O ring seal kits, nor do they supply these parts to dealers. They only sell entire component blocks or levels where the cost to you is much higher, often hundreds of dollars higher; 99.99% of the time the large components that Kinetico service engineers would fit only require small seals fitting. These components include the inlet and purge valves which mostly only require new quad rings, together with drain valves and control valves, and some other simple seals and parts; these mostly solve most of the faults that Kinetico softeners develop.

If your Kinetico Softener looks similar to the one shown here our Rebuild Kit will fit your softener. If your Kinetico head, looks like this model shown above, maybe has different resin storage, you will be able to service yours too. The design is common to all softeners.

Most Kinetico water softeners will run for many years without fault. However, when faults do occur the actual fault is often a very simple thing to rectify; what is more, they mostly only need cleaning to bring back to life. The Videos will show you how to break down, clean/service and assemble. We show clearly main problem points and what to look out for. We include breakdown of parts and fault finding in PDF format.

We include full exploded drawings of Water Softener PDF. We include full fault finding diagnosis charts PDF. We include detailed descriptions of parts PDF. There is a full detailed breakdown of the Kinetico water softener metering system head and full breakdown.

Of all levels of the head. The Video provides a full tutorial which you can use to dismantle and re-assemble. We show where to clean and where to use the important silicone grease to maintain.

Save a fortune on Service calls. Hours of Video to Watch in Real Time? Our Kinetico Engineer Shows You How. The Unique Kinetico Re-Build Pack. Kinetico Water Softener Service Pack.

Complete Kinetico Quad Ring Kit. Now including the special Silicone O ring set - Very difficult to obtain normally. And also let us be very clear, you would likely only need to replace the seal kit once in your softeners lifetime. But, the super Video Tutorials can be used again and again for regular service intervals.

This really is a special deal. Now we include the important seals within the Kinetico Softener Head.

Videos and Low Cost Kinetico Softener Parts. Packaging May be Different to as Shown.